Last updated on October 12th, 2021 at 03:42 pm
On Quora, a man named Becky shared his disaster experience. In his story, he grabbed a new car recently, and suddenly it got stuck by the truck. He needed to repair the steering pump or replace it with an expert immediately.
The very next day, he went to the pulley stores to rent a pulley puller kit, but they were fresh out and didn’t have any models for sale that fit his car. And finally, he was going to be hopeless and asked the same question on Quora, “How To Remove Power Steering Pump Pulley Without Puller?”
This awkward moment can usually happen to any of us. Then, what’s the solution?
Here I will guide you through a few simple steps to find the best answer to your question.
So, without further ado, let’s dive in..
How To Remove Power Steering Pump Pulley Without Puller
In this post, I attach possible ways about how to remove pulleys from power steering pumps and related issues. So, make sure to read out first to last.
As we know, it’s pretty tricky to find a task on how to remove power steering pump pulley without puller. Thankfully, I’ve discovered some simple tricks on it. My goal is here to vivid those following subtopics within this writing.
How To Remove a Power steering pulley without puller?
How to remove the power steering pump from the reservoir?
How to steal a power steering pulley bolt?
How to install a power steering pulley without a tool?
How to reduce the harmonic balancer without using a puller?
We are getting started by taking some pre-removal necessary steps-
- Place the car/ vehicle on the ground level, park it in the relevant places.
- Before starting the work, make sure that the engine was cool.
- Avoid working on the heated engine.
- Ensure that you put the parking brake.
- Keep your vehicle hood open.
- Keep the battery disconnected while you’re starting the task.
5 Easiest Steps on How to Remove power steering Pump Pulley Without Puller
Step – 1 Remove The Main Drive Pulley & Re-affix it
Remove the main drive pulley and reinstalled it. It will help to press into the input shaft to improve the internal pump. The joint venture between the inner shaft & pump allows the engine to transfer power from a serpentine belt to the pulley.
Step- 2 Clean The Pulley Pump
Remove the tool from the pump. It can take up to 12 inches long in front of the pump. Afterward, clean and remove the pump. You’ll find a mounting bracket here for sufficient room. Once you got it, fit the tool forcefully and press it to keep it in a perfect position.
Step- 3 Keep The Temperature About 120-130⁰ F & Press The Input Shafts
You will hear a pop that informs you that the pulley got started. Don’t forget to warm up about 120-130⁰ Fahrenheit; then reinstall it. You should continue to press and force it to get positioned until the pulley becomes free enough to pump input shafts.
Step- 4 Spin The Shafts & Mount It Gently
As we mentioned before, we want the pulley to warm at least 120-130⁰. Once the pulley achieves the exact temperature, align it onto the shaft. Next, you need to spin it until the pulley ensures the square mount politely. Remember, a square mount will start to work when you form it correctly before installation. Installation of the pulley must be done in a clean, rust-free shaft. If it is not cleaned, the installation program is more lengthy and complicated then.
Disclaimer –
Avoid lubricating the pulley or shaft with any grease, oil, or liquid. If there are any changes to present any grease or oil, clean it before installation. It can cause the pulley to slip and fail your mission.]
Step- 5 Keep Tightened The Tool & Re-installed It
Turn the pulley on > take the wobble out from it. Connect the installation tool with the input shaft pump> tighten the collar against the pulley. Again, continue to tighten the installation using a wrench/ ratchet. Keep tightening the tool continuously until the power steering pulley is installed. Flush it along with the shaft to make sure the installation is done completely.
FAQs :
1. How to remove the power steering pump from the reservoir?
Find out the location of the power steering pump. Next, place the reservoir on the body of the steering pump. You’ll find two metal tabs hold the pool to the pump body. With the help of a screwdriver, pull out the reservoir from its body and pry these all together.
You can see a metal nipple coming out from the pump and ensuring the O ring didn’t distract from it. Afterward, you can replace the reservoir with the new one.
2. How to install power steering pump pulley-chevy?
To install a power steering pump in your Chevy –
- Disclose the black & negative battery cable of the vehicle.
- With a tube wrench, eradicate the line from the pump.
- Place an old cloth under the bar to catch dripping fluid or junk.
Next, remove the 2-mounting bolts from it. Lift the pump off into the engine compartment. Finally, set out the new power steering pump in place and tighten the nuts back. Check out the engine efficiency then.
3. How To Steal Power Steering Pulley Bolt?
The easiest and most g way to steal a power steering pulley bolt is by impacting it with a jolt tool. Another way is to unbolt it using a screwdriver or a wrench. Keep in mind that all you need to do is remove the bolt counterclockwise and tighten it back clockwise. https://theautoly.com/how-does-a-steering-wheel-lock-work.
4. How to install power steering pulley without a tool?
Remember, the pulley is an interference fit, and it is held captive by that, which means the diameter of the shaft is, for example, 1-inch diameter.
The hole in the pulley is about a few thousandths of an inch smaller, like 0.996. That means the interface is 0.004 thousandth.
To install it without a tool, you can heat the area around the hole with a torch to expand. It’s enough to slip on. Do not turn the metal rod, and straw-yellow is enough. You can install it by putting the pump in the freezer, which will shrink the diameter of the shaft.
5. How to reduce the harmonic balancer without using a puller?
First, access the balancer by removing the serpentine belt. Find out the center bolt and remove it using a wrench or socket. Finally, remove the pulley and remove the harmonic balancer with a durable strap.
Final Wrap
In summary, you may have recently found out different solutions on how to remove power steering pump pulley without puller by the blessings of many social sites.
You know, there’s no shortcut to becoming successful. Allegorically, removing pulleys without a puller seems to be more difficult than hear. It’s an obvious process for those who do not have the money or time to do it with tools.
But, if you don’t have any financial issues, you must have an exceptional power steering pulley for pulleys that have just an outer slot on the hub to grab.
Hope you find my solutions and ways helpful.
More Search – How To Remove Wheel Locks Without Key?